<span id="ob18j"></span>
  • <sup id="ob18j"><center id="ob18j"><menu id="ob18j"></menu></center></sup>

    
    

      1. <style id="ob18j"><delect id="ob18j"><source id="ob18j"></source></delect></style>
        1. 中文版 ENGLISH JAPANESE
          Welcome to the official website of Huizhou Youhui Intelligent Equipment Co., Ltd!

          Company news

          Your current position is: Home >>Latest news >>Company news >>Common faults and causes of winding machine

          Common faults and causes of winding machine

          Release time:2021-05-06

          Motor in the automatic winding machine is one of the most important power components, common asynchronous motor, servo motor, stepper motor, dc motor, etc., each plays a different role be short of one cannot, in daily use often encounter failure of the motor, this paper simply explain the motor fault and causes.


          The first is the lack of phase operation of the general fault phenomenon is: the motor can not start, even if no load can start, speed slowly rise, there is a buzz;

          Motor smoke heating, and accompanied by burning smell, the cause is the following possible: power supply loop fuse loop contact or mechanical damage, resulting in a phase fuse fuse, motor power supply loop three-phase fuse specifications are different, small capacity fuse burned.

          According to the power of the motor, it should be replaced with the fuse of the same specification, the switches in the power supply circuit of the motor (isolator switch, rubber cover switch, etc.) and the contacts in contact with poor contact (burn or loose).

          Repair and adjust the dynamic and static contacts, so that the contact is good, and the connection between the motor windings is falsely welded, resulting in poor contact. Carefully check the connection of the motor windings and weld them firmly.


          The second kind of fault phenomenon is the overload operation that the motor current exceeds the rated value;

          When the temperature rise of the motor exceeds the rated temperature rise, the general cause of the fault is:

          Under the heavy load, want to consider appropriate lightening or replace capacity suitable motor, power supply voltage is too high or too low, need to install three-phase power supply voltage compensation cabinet, motor long-term serious be affected with damp be affected with damp or corrosive gas corrosion, insulation resistance decline, should according to the specific situation, for repair or replacement of the same capacity, and specifications of the enclosed motor, transmission part fails,

          Causes the motor to overload and burns out the motor winding.


          The third common fault is winding short circuit, the main performance of the motor output torque drop, motor buzzing, and obvious heating, motor smoke until burned.

          At this time, the short-circuit current is particularly large, and the three-phase current increases.

          Damp environment or vibration and pollution into the motor caused.

          With the resistance method and short circuit detection device can be measured the corresponding data and short circuit point, are generally caused by damp environment or vibration and pollution into the motor.

          The corresponding data and short circuit point can be measured by means of resistance method and short circuit detector.


          Finally, the stator winding single-phase short circuit, the fault phenomenon is: the motor speed decreased significantly, the two-phase current rose sharply, the motor issued a strong buzz, the winding soon heating;

          Over time, part of the motor winding will be burned, general star will have two-thirds of winding burned, triangular meet will have a third winding burned, cause of the failure is the winding insulation damage, a three-phase asynchronous motor with load fuse fusing and contactor a pair of contactor disconnect the one-way operation caused.

          The user should pay more attention to the abnormal noise, temperature rise and smell of the equipment in the normal use process, and the fault should be promptly shut down and repaired to minimize the damage.


          Youhui machinery independent research and development and production of the winding machine, fully protect the use of users, under any circumstances to provide life-long perfect follow-up after-sales service!

          Service hotline: 4008-333-718

          返回頂部
          97久久综合欧美久久_手机最新入口婷婷一区_久久狠狠中文字幕_亚欧无码一区二区 国产亚洲日韩av在线 欧美一级婬片人妻欧美大
          <span id="ob18j"></span>
        2. <sup id="ob18j"><center id="ob18j"><menu id="ob18j"></menu></center></sup>

          
          

            1. <style id="ob18j"><delect id="ob18j"><source id="ob18j"></source></delect></style>
              1. 动漫精品V欧美精品V日韩精品| 特黄毛片| 国产又粗又猛又黄又爽无遮挡| 国产亚洲精品综合一区91555| 日日夜夜免费视频| 欧美牲交a欧美牲交一级aa| 国产人免费人成免费视频| 亚洲精品无码AV中文字幕| ,国产狂喷潮视频免费观看| 亚洲视频一区二区| 欧美精品在线观看| -99精品国产在热2019一级毛片| 女人麻豆国产香蕉久久精品视频| 久久精品无码不卡| 亚洲一区无码AV在线播放| 亚洲一区二区三区在线| 欧美国产一区二区三区| 天天亚洲综合视频| 国产福利小视频在线| 超碰在线免费|